ES-0891 Rev.14
10BX
High-density Signal Conditioners 10-RACK
STANDARD RACK
Functions & Features
• Standard 19" rack for 10-RACK signal conditioners
• 4 – 16 modules mountable
• Line power access at the terminal card, supplied via the rear rack bus
• Direct interface to various DCS with the rack side connector
MODEL: 10BX–[1][2]
ORDERING INFORMATION
• Code number: 10BX-[1][2]
Specify a code from below for each of [1] and [2].
(e.g. 10BX-1/W/Q)
• Specify the specification for option code /Q
(e.g. /C01)
[1] CAPACITY & TERMINAL CARD FUNCTION
1
: 16 ch.; 24 V DC powered
2-K
: 15 ch.; 85 – 132 V AC powered
2-L
: 15 ch.; 170 – 264 V AC powered
3
: 15 ch.; 24 V DC & 85 – 132 V AC powered
(two independent power sources)
4
: 16 ch.; 24 V DC (Fujitsu FCN type I/O connector)
7
: 16 ch.; 24 V DC (Yokogawa VMx / PM1 card use)
8
: 16 ch.; 24 V DC (Omron 3G8B2-NA000 / NA001 use)
10
: 16 ch.; 24 V DC (Nippon Shokubai DCS use)
11
: 16 ch.; 24 V DC (Azbil J-HAM50 / J-HMM00 module use)
12
: 16 ch.; 24 V DC (Azbil J-AOM10 module use)
13
: 8 ch.; 24 V DC (Azbil J-PIM00 module use)
A
: 4 ch.; 24 V DC powered
B
: 4 ch.; 85 – 132 V AC powered
C
: 9 ch.; 24 V DC powered
D-K
: 8 ch.; 85 – 132 V AC powered
D-L
: 8 ch.; 170 – 264 V AC powered
We guarantee the connecting section.
[2] OPTIONS (multiple selections)
Mounting Bracket
blank
: Rack mounting, standard
/W
: Surface mounting
Other Options
blank
: none
/Q
: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to our web site.)
Power supply and signal conditioner side of the main PWB are not coated.
/C01
: Silicone coating
/C02
: Polyurethane coating
/C03
: Rubber coating
RELATED PRODUCTS
• Blank filler plate (model: P-101)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
GENERAL SPECIFICATIONS
Construction
: Metal plates assembly
Coating
: Zn-Cr (black), alumetized steel
Connection
Power input
: M4 screw terminals (torque 0.8 N·m)
Screw terminal
: Nickel-plated brass
Isolation
: I/O connector to power to FG
INSTALLATION
Power consumption
•
AC
: 85 – 132 V or 170 – 264 V, 47 – 63 Hz, 130 VA minimum
•
DC
: Operating voltage range 24 V DC ±10 %, 2.5 A minimum (ripple 10 % p-p max.)
Operating temperature
: -5 to +55°C (23 to 131°F) 0 to 50°C (32 to 122°F) for AC power
Operating humidity
: 30 to 90 %RH (non-condensing)
Mounting
15, 16-position rack, 10BX-13
: JIS or EIA standard rack or surface
4, 8, 9-position rack
: Angle bracket or surface
Weight
10BX-1, 4, 7, 8, 10, 11, 12, 13, D
: 1.9 kg (4.2 lb)
10BX-2, 3
: 2.3 kg (5.1 lb)
10BX-A
: 1.1 kg (2.4 lb)
10BX-B
: 1.3 kg (2.9 lb)
10BX-C
: 1.5 kg (3.3 lb)
PERFORMANCE
Insulation resistance
: ≥ 100 MΩ with 500 V DC
Dielectric strength
:
500 V AC @ 1 minute (I/O connector to power)
1500 V AC @ 1 minute (power to FG)
500 V AC @ 1 minute (1000 V for 24 V DC) (I/O connector to FG)
MOUNTING REQUIREMENTS
DIMENSIONS unit: mm (inch)
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
I/O CONNECTOR PIN ASSIGNMENT