ES-2362 Rev.4

IT60RC

Tower Light Series

CC-Link TOWER LIGHT

(60 mm dia., 4 layers)
Functions & Features
• Lighting, blinking and buzzing are controllable with PLC.
• Bi-color lighting available in fourth layer
• Separable tension clamp terminal

MODEL: IT60RC-4[1][2][3][4][5]D[6]-[7][8]

ORDERING INFORMATION

• Code number: IT60RC-4[1][2][3][4][5]D[6]-[7][8]
Specify a code from below for each of [1] through [8].
  (e.g. IT60RC-4RYGBWD1-M2/Q)
• Specify the specification for option code /Q
  (e.g. /C01)

LAMP LAYERS

4: 4 layers

[1] LAMP 1 COLOR

(1st layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[2] LAMP 2 COLOR

(2nd layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[3] LAMP 3 COLOR

(3rd layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[4] LAMP 4 COLOR

(4th layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[5] LAMP 5 COLOR

R: Red
Y: Amber
G: Green
B: Blue
W: White
N: None

MOUNTING

D: Direct mounting

[6] DESIGN TYPE

1: Type 1
2: Type 2 (with dummy antennae)
(refer to outline dimensions)

[7] POWER INPUT

AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
 47 – 66 Hz)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[8] OPTIONS

blank: none
/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to our web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating

GENERAL SPECIFICATIONS

Degree of protection: IP 65, vertical mounting only (bottom connectors excluded)
Connection
  Power/Network
: Separable tension clamp terminal
  Applicable wire size: 0.2 to 1.5 mm2, stripped length 10 mm
Recommended solderless terminal
  AI0,5-10WH 0.5mm2 (Phoenix Contact)
  AI0,75-10GY 0.75mm (Phoenix Contact)
Housing material: Flame-resistant resin (white)
Lens: Flame-resistant resin (transparent)
Isolation: Network to power input to FE1 (Functional Earth)
DIP SW Setting: Frequency of lamp blinking and buzzing discontinuance, buzzing volume level and output at connection failed. (refer to the instruction manual)
Lamp: Red, amber, green, blue and white LEDs
on/blinking (approx. 2 Hz, 10 Hz)
Indicator LEDs: Power, Run, Error, SD and RD (5 LEDs) indicate the module’s operating conditions. (Refer to the insruction manual)
Buzzing: Approx. 3.3 kHz
  Interval: continuous/intermittent (approx. 2 Hz, 10 Hz)

CC-Link COMMUNICATION

Protocol: CC-Link V1.10
Device type: Remote I/O station
Station No. setting: Rotary switch; 1 – 64
Required node: 1
Baud rate setting: Rotary switch
156kbps, 625kbps, 2.5Mbps, 5Mbps, 10Mbps
Cable for comm. link: Specified by Mitsubishi Electric
Terminating resistor: Built-in (Selected with the DIP SW)

INSTALLATION

Power consumption
AC: Approx. 5 VA at 100 V
  Approx. 7 VA at 200 V
  Approx. 8 VA at 240 V
DC: Approx. 3 W
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas
Mounting: Direct mounting
Mounting direction: Vertical
Weight: 1.4 kg (3.1 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(network to power to FE1)

EXTERNAL VIEW

TERMINAL ASSIGNMENTS

EXTERNAL DIMENSIONS unit: mm

MOUNTING REQUIREMENTS unit: mm

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM