ES-5041 Rev.14
M2AVS
Super-mini Signal Conditioners Mini-M Series
DC ALARM
Functions & Features
• Provides N.O. relay outputs at preset DC input levels
• Dual trip
• Multi-turn potentiometer adj.
• Monitor jacks help setpoint adj.
• Power ON timer
• Relays can be powered 110 V DC
Typical Applications
• Annunciator
• Various alarm applications
MODEL: M2AVS–[1][2][3][4]–[5][6]
ORDERING INFORMATION
• Code number: M2AVS-[1][2][3][4]-[5][6]
Specify a code from below for each of [1] through [6].
(e.g. M2AVS-6112-R/CE/Q)
• Special input range (For codes Z, 0 & 01)
• Specify the specification for option code /Q
(e.g. /C01/S01)
[1] INPUT
Current
A
: 4 – 20 mA DC (Input resistance 250 Ω)
A1
: 4 – 20 mA DC (Input resistance 50 Ω)
B
: 2 – 10 mA DC (Input resistance 500 Ω)
C
: 1 – 5 mA DC (Input resistance 1000 Ω)
D
: 0 – 20 mA DC (Input resistance 50 Ω)
E
: 0 – 16 mA DC (Input resistance 62.5 Ω)
F
: 0 – 10 mA DC (Input resistance 100 Ω)
G
: 0 – 1 mA DC (Input resistance 1000 Ω)
H
: 10 – 50 mA DC (Input resistance 100 Ω)
J
: 0 – 10 μA DC (Input resistance 1000 Ω)
K
: 0 – 100 μA DC (Input resistance 1000 Ω)
GW
: -1 – +1 mA DC (Input resistance 1000 Ω)
FW
: -10 – +10 mA DC (Input resistance 100 Ω)
Z
: Specify current (See INPUT SPECIFICATIONS)
Voltage
1
: 0 – 10 mV DC (Input resistance 10 kΩ min.)
15
: 0 – 50 mV DC (Input resistance 10 kΩ min.)
16
: 0 – 60 mV DC (Input resistance 10 kΩ min.)
2
: 0 – 100 mV DC (Input resistance 100 kΩ min.)
3
: 0 – 1 V DC (Input resistance 1 MΩ min.)
4
: 0 – 10 V DC (Input resistance 1 MΩ min.)
5
: 0 – 5 V DC (Input resistance 1 MΩ min.)
6
: 1 – 5 V DC (Input resistance 1 MΩ min.)
4W
: -10 – +10 V DC (Input resistance 1 MΩ min.)
5W
: -5 – +5 V DC (Input resistance 1 MΩ min.)
0
: Specify voltage (See INPUT SPECIFICATIONS)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
01
: Specify voltage (See INPUT SPECIFICATIONS)
(Select ‘/CE’ for ‘Standards & Approvals’ code.)
[2] SETPOINT 1 OUTPUT
1
: Hi (coil energized at alarm)
3
: Lo (coil energized at alarm)
[3] SETPOINT 2 OUTPUT
1
: Hi (coil energized at alarm)
3
: Lo (coil energized at alarm)
[4] OUTPUT
2
: Relay; N.O. or make contact
6
: Photo MOSFET relay; N.O.
[5] POWER INPUT
AC Power
M
: 85 – 264 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
DC Power
R
: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
R2
: 11 – 27 V DC
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
P
: 110 V DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
[6] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N
: Without CE
/CE
: CE marking
Other Options
blank
: none
/Q
: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to our web site.)
/C01
: Silicone coating
/C02
: Polyurethane coating
/C03
: Rubber coating
/C04
: Polyolefin coating
TERMINAL SCREW MATERIAL
/S01
: Stainless steel
GENERAL SPECIFICATIONS
Construction
: Plug-in
Connection
: M3 screw terminals (torque 0.8 N·m)
Screw terminal
: Chromated steel (standard) or stainless steel
Housing material
: Flame-resistant resin (black)
Isolation
: Input to output 1 to output 2 to power
Setpoint adjustments
: Multi-turn screwdriver adjustments (front); 0 – 100 % independently
Monitor jacks
: Output 0 – 1 V for 0 – 100 % setpoints
Hysteresis (deadband)
: ≤ 0.5 %
Front LEDs
Output 1
: Red LED turns on when the coil is energized.
Output 2
: Green LED turns on when the coil is energized.
Power ON timer
: Relays de-energized for approx. 1 seconds after power is turned on.
INPUT SPECIFICATIONS
■
DC Current
:
Shunt resistor attached to the input terminals (0.5 W)
Specify input resistance value for code Z.
■
DC Voltage
: -300 – +300 V DC
(-30 – +30 V for the input code 01. Span 30 V max.)
Minimum span
: 3 mV
Offset
: Max. 1.5 times span
•
Input resistance
Span 3 – 10 mV : ≥ 10 kΩ
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
Span ≥ 1 V : ≥ 1 MΩ
OUTPUT SPECIFICATIONS
■
Relay Contact
:
120 V AC @0.5 A (cos ø = 1)
240 V AC @0.5 A (cos ø = 1)
30 V DC @0.5 A (resistive load)
Maximum switching voltage
: 250 V AC or 120 V DC
Maximum switching power
: 120 VA or 15 W (≤ 0.5 A)
Minimum load
: 5 V DC @10 mA
Mechanical life
: 5 × 10
7
cycles
For maximum relay life with inductive loads, external protection is recommended.
■
Photo MOSFET Relay
Maximum switching voltage
: 30 V AC or 50 V DC
Maximum switching current
: 0.5 A
ON resistance
: ≤ 2 kΩ
Leakage current at OFF
: ≤ 10 μA
For maximum relay life with inductive loads, external protection is recommended.
INSTALLATION
Power Consumption
•
AC
:
Approx. 3 VA at 100 V
Approx. 4 VA at 200 V
Approx. 5 VA at 264 V
•
DC
: Approx. 3 W
Operating temperature
: -5 to +55°C (23 to 131°F)
Operating humidity
: 30 to 90 %RH (non-condensing)
Mounting
: Surface or DIN rail
Weight
: 150 g (0.33 lb)
PERFORMANCE in percentage of span
Setpoint monitor accuracy
: ±0.5 %
Temp. coefficient
: ±0.05 %/°C (±0.03 %/°F)
Response time
: ≤ 0.5 sec. (0 – 100 % at 90 % setpoint)
Line voltage effect
: ±0.1 % over voltage range
Insulation resistance
: ≥ 100 MΩ with 500 V DC
Dielectric strength
: 2000 V AC @1 minute (input to output 1 to output 2 to power to ground)
STANDARDS & APPROVALS
EU conformity
:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Measurement Category II (output)
Installation Category II (power)
Pollution Degree 2
Input to output to power: Basic insulation (300 V)
RoHS Directive
FRONT VIEW
Refer to the instruction manual for detailed procedures.
EXTERNAL DIMENSIONS unit: mm [inch]
TERMINAL ASSIGNMENTS unit: mm [inch]
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM