ES-7799 Rev.9
R7F4DH
Remote I/O R7F4D Series
HI-SPEED LINK SYSTEM I/O MODULE
MODEL: R7F4DH-[1]-[2]-R[3]
ORDERING INFORMATION
• Code number: R7F4DH-[1]-[2]-R[3]
Specify a code from below for each of [1] through [3].
(e.g. R7F4DH-1-DA16A-R/H/Q)
• Specify the specification for option code /Q
(e.g. /C01)
[1] TERMINAL BLOCK
1
: Tension clamp terminal block for power supply
RJ-45 Modular jack for communication
e-CON connector for I/O
2
: Tension clamp terminal block for power supply
RJ-45 Modular jack for communication
MIL connector 1 for I/O
3
: Tension clamp terminal block for power supply
RJ-45 Modular jack for communication
MIL connector 2 for I/O
4
: Tension clamp terminal block for power supply
RJ-45 Modular jack for communication
Tension clamp terminal block for I/O
[2] I/O TYPE
DA16A:
NPN discrete input, 16 points
DA16B:
PNP discrete input, 16 points
DC16A
: NPN transistor output, 16 points
DC16B
: PNP transistor output, 16 points
DAC16A
: PNP discrete input &
NPN transistor output, 8 points each
DAC16B
: NPN discrete input &
PNP transistor output, 8 points each
DAC16C
: NPN discrete input &
NPN transistor output, 8 points each
DAC16D
: PNP discrete input &
PNP transistor output, 8 points each
DAC32A
: PNP discrete input &
NPN transistor output, 16 points each
(Only terminal block codes 2, 3 selectable)
DAC32B
: NPN discrete input &
16 points PNP transistor output, 16 points each
(Only terminal block codes 2, 3 selectable)
DAC32C
: NPN discrete input &
16 points NPN transistor output, 16 points each
(Only terminal block codes 2, 3 selectable)
DAC32D
: PNP discrete input &
PNP transistor output, 16 points each
(Only terminal block codes 2, 3 selectable)
POWER INPUT
DC Power
R
: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[3] OPTIONS (multiple selections)
Communication Mode
blank
: Full-duplex
/H
: Half-duplex
Other Options
blank
: none
/Q
: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to our web site.)
/C01
: Silicone coating
/C02
: Polyurethane coating
/C03
: Rubber coating
FUNCTIONS & FEATURES
The R7F4DH interfaces discrete I/O signals with a PLC via HLS.
(HLS is the abbreviation for “Hi-speed Link System” of Step Technica Co., Ltd.)
GENERAL SPECIFICATIONS
•
Common Specifications
Power input
: 24 V DC ±10 %; ripple 10 %p-p max.; rated current 8 A
Sensor excitation
: 24 V DC ±10 %; ripple 5 %p-p max.,
≤ 2 A (including discrete I/O load charge);
rated current 8 A
Insulation resistance
: ≥ 100 MΩ with 500 V DC
Dielectric strength
: 1500 V AC @1 minute
(between isolated circuits)
Operating temperature
: -10 to +55°C (14 to 131°F)
Operating humidity
: 30 to 90 %RH (non-condensing)
Atmosphere
: No corrosive gas or heavy dust
Mounting
: DIN rail or wall
Housing material
: Flame-resistant resin (gray)
Status indicator
: Power LED on with power supplied
Discrete I/O status indicator
: Red LED on at contact on. (For R7F4DH-x-DAC32x, input or output display is selected with slide SW; factory setting: input display)
Communication Failure Detection
: At communication error, the output status until normal data is received (Hold or OFF) can be set with the DIP SW. (only for output devices; factory setting: Hold)
■
Current Consumption & Weight
R7F4DH-x-DA16A: Approx. 25 mA/100 g (0.22 lb)
R7F4DH-x-DA16B: Approx. 25 mA/100 g (0.22 lb)
R7F4DH-x-DC16A: Approx. 50 mA/100 g (0.22 lb)
R7F4DH-x-DC16B: Approx. 50 mA/100 g (0.22 lb)
R7F4DH-x-DAC16A: Approx. 35 mA/100 g (0.22 lb)
R7F4DH-x-DAC16B: Approx. 35 mA/100 g (0.22 lb)
R7F4DH-x-DAC16C: Approx. 35 mA/100 g (0.22 lb)
R7F4DH-x-DAC16D: Approx. 35 mA/100 g (0.22 lb)
R7F4DH-x-DAC32A: Approx. 40 mA/120 g (0.27 lb)
R7F4DH-x-DAC32B: Approx. 40 mA/120 g (0.27 lb)
R7F4DH-x-DAC32C: Approx. 40 mA/120 g (0.27 lb)
R7F4DH-x-DAC32D: Approx. 40 mA/120 g (0.27 lb)
(Discrete I/O load charge is not included in the above-mentioned current consumption.)
HLS COMMUNICATION
Communication mode
: Full-duplex or half-duplex
Network cable
Full-duplex communication:
ZHY262PS and ZHT262PS (Shinko Seisen Industry Co., Ltd.)
Half-duplex communication:
ZHY221PS (Shinko Seisen Industry Co., Ltd.)
Dual-shield cable:
ZHY262PBA (Shinko Seisen Industry Co., Ltd.)
Transmission distance
:
12 Mbps: 100 meters (328 ft)
6 Mbps: 200 meters (656 ft)
3 Mbps: 300 meters (984 ft)
(Baud rate configurable with DIP SW; factory setting: 12 Mbps)
Terminating resistor
: Built-in (Selected with the DIP SW; factory setting: disabled)
Status indicator
: Run LED on in normal communication
Station address
: Set with rotary switch
(Refer to the instruction manual for details.)
STANDARDS & APPROVALS
Refer to the manuals to comply with the standards.
EU conformity
:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EXTERNAL VIEW
■ TERMINAL BLOCK CODE 1 (e-CON)
■ TERMINAL BLOCK CODE 2, 3 (MIL)
■ TERMINAL BLOCK CODE 2,3 (MIL, 32 pin)
■ TERMINAL BLOCK CODE 4 (Tension Clamp)
CONNECTION DIAGRAMS
■
I/O connection (Refer to each model terminal assignment)
•
e-CON connector
Recommended cable connector
: 37104-( )-000FL (3M Company)
(The cable connector is not included in the package.
Specify wire size instead of ( ); refer to the specifications of the product.)
•
MIL connector
Recommended cable connector
: XG4M-2030 (Omron)
(The cable connector is not included in the package.)
•
Tension clamp terminal block
Cable connector
: FMC1,5/16-ST-3,5 (Phoenix Contact)
(The cable connector is included in the package.)
Applicable wire size
: 0.2 − 1.5 mm
2
; stripped length 10 mm
Recommended solderless terminal
- AI0,25−10YE 0.25 mm
2
(Phoenix Contact)
- AI0,34−10TQ 0.34 mm
2
(Phoenix Contact)
- AI0,5−10WH 0.5 mm
2
(Phoenix Contact)
- AI0,75−10GY 0.75 mm
2
(Phoenix Contact)
- A1−10 1.0 mm
2
(Phoenix Contact)
- A1,5−10 1.5 mm
2
(Phoenix Contact)
I/O DATA DESCRIPTIONS
EXTERNAL DIMENSIONS unit: mm [inch]
■ TERMINAL BLOCK CODE 1 (e-CON)
■ TERMINAL BLOCK CODE 2, 3 (MIL)
■ TERMINAL BLOCK CODE 2, 3 (MIL, 32 pin)
■ TERMINAL BLOCK CODE 4 (Tension Clamp)
MOUNTING REQUIREMENTS unit: mm [inch]