ES-2377 Rev.8
IT60SA1
Tower Light Series
DISCRETE INPUT TOWER LIGHT
(small size, 60 mm dia., 1 - 5 layers)
Functions & Features
• Discrete input tower light
• Lighting, blinking and buzzing are controllable with PLC.
• Switchable between positive and negative common for input
MODEL: IT60SA1-[1][2][3][4][5][6]D1-[7][8]
ORDERING INFORMATION
• Code number: IT60SA1-[1][2][3][4][5][6]D1-[7][8]
Specify a code from below for each of [1] through [8].
(e.g. IT60SA1-5RYGBWD1-M2/Q)
• Use Ordering Information Sheet (No. ESU-2375) to select the same color for more than one layer.
• Specify the specification for option code /Q
(e.g. /C01)
[1] LAMP LAYERS
1
: 1 layer
2
: 2 layers
3
: 3 layers
4
: 4 layers
5
: 5 layers
[2] LAMP 1 COLOR
(1st layer from the top)
R
: Red
Y
: Amber
G
: Green
B
: Blue
W
: White
[3] LAMP 2 COLOR
(2nd layer from the top)
R
: Red
Y
: Amber
G
: Green
B
: Blue
W
: White
N
: None (not available when Lamp Layers selected are 2 - 5)
[4] LAMP 3 COLOR
(3rd layer from the top)
R
: Red
Y
: Amber
G
: Green
B
: Blue
W
: White
N
: None (not available when Lamp Layers selected are 3 - 5)
[5] LAMP 4 COLOR
(4th layer from the top)
R
: Red
Y
: Amber
G
: Green
B
: Blue
W
: White
N
: None (not available when Lamp Layers selected are 4 - 5)
[6] LAMP 5 COLOR
(5th layer from the top.)
R
: Red
Y
: Amber
G
: Green
B
: Blue
W
: White
N
: None (not available when Lamp Layers selected are 5)
* Select "None" option for the layers other than the selected.
MOUNTING
D
: Direct mounting
DESIGN TYPE
1
: Type 1
(refer to outline dimensions)
[7] POWER INPUT
AC Power
M2
: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
DC Power
R
: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[8] OPTIONS
blank
: none
/Q
: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to our web site.)
/C01
: Silicone coating
/C02
: Polyurethane coating
/C03
: Rubber coating
RELATED PRODUCTS
• Mounting Pole (model: ITPL, ITB, ITP, ITW and ITS)
• Mounting Adapter (model: ITAD1, ITAM, ITAR and ITAW)
GENERAL SPECIFICATIONS
Degree of protection
: IP 65, vertical mounting only (bottom excluded)
Connection
Power
: UL1007 AWG20
Input
: UL1007 AWG22
Housing material
: Flame-resistant resin
Lens
: Flame-resistant resin (transparent)
Isolation
: Input to power input to FE1 (Functional Earth) (M2 power input only)
DIP SW Setting
: Refer to the instruction manual
• Buzzer volume level
• Buzzer intermittent frequency
• Lamp blinking frequency
Lamp
: Red, amber, green, blue and white LEDs
on/blinking (approx. 2 Hz, 10 Hz)
Status indicator
Power
: Green LED turns ON in normal operating conditions.
Buzzing
: Approx. 3.3 kHz
Interval
: continuous/intermittent (approx. 2 Hz, 10 Hz)
INPUT SPECIFICATIONS
■
Discrete Input
: Dry contact, open collector PNP or NPN
Conformity contact
:
Load voltage
: ≥ 35 V DC
Load current
: ≥ 50 mA/point
Residual voltage
: ≤ 0.5 V
Leakage current
: ≤ 0.1 mA
PNP is not available for 100 – 240 V AC power.
INSTALLATION
Power consumption
•
AC
: Approx. 8 VA @ 100 V
Approx. 10 VA @ 200 V
Approx. 11 VA @ 240 V
•
DC
: Approx. 4.1 W; approx. 170 mA
Operating temperature
: -10 to +55°C (14 to 131°F)
Operating humidity
: 30 to 90 %RH (non-condensing)
Atmosphere
: No corrosive gas
Mounting
: Direct mounting
Mounting direction
: Vertical
Weight
: 750 g (1.65 lb)
PERFORMANCE
Insulation resistance
: ≥ 100 MΩ with 500 V DC (M2 power only)
Dielectric strength
: 1500 V AC @ 1 minute (input to power to FE1; M2 power only)
STANDARDS & APPROVALS
EU conformity
:
EMC Directive
EN 60947-5-1
Low Voltage Directive
EN 60947-5-1
・24 V DC power
Installation Category III
Pollution Degree 3
・100 – 240 V AC power
Installation Category II
Pollution Degree 2
Input to power: Reinforced insulation (300 V)
RoHS Directive
Protection against access to the terminal blocks
:
Finger protection (VDE 0660-514)
EXTERNAL VIEW
EXTERNAL DIMENSIONS unit: mm
MOUNTING REQUIREMENTS unit: mm
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM