ES-9308 Rev.12

SHSP

8-PORT ETHERNET SWITCH

(with surge protector)
Functions & Features
• Surge protector function for each port
• Protects Ethernet devices from surges entering through LAN cables
• Surge protector life monitor function with LED and contact output alarm
• Data transfer rate can be fixed
Typical Applications
• Risk managed system

MODEL: SHSP–1–[1][2]

ORDERING INFORMATION

• Code number: SHSP-1-[1][2]
Specify a code from below for each of [1] and [2].
  (e.g. SHSP-1-R/CE/Q)
• Specify the specification for option code /Q
  (e.g. /C01/SET)

SURGE PROTECTOR

1: With

[1] POWER INPUT

AC Power
M2: 100 – 240V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
(Select ‘/CE’ for ‘Standards & Approvals’ code.)

[2] OPTIONS (multiple selections)

Standards & Approvals (must be specified)
/N: Without CE
/CE: CE marking
Other Options
blank: none
/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to our web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
 (No. ESU-9308)

RELATED PRODUCTS

• PC Configurator cable (model: MCN-CON or COP-US)
• PC configurator software (model: SHSPCFG)
Downloadable at our web site.

GENERAL SPECIFICATIONS

Surge protection: All ports
Connection
Ethernet: RJ-45 connector
Power input, grounding, alarm contact output:
M3 separable screw terminal (torque 0.8 N·m)
PC configurator: Miniature jack
Screw terminal: Nickel-plated steel
Housing material: Steel, melamine baking finish (black)
Monitor LED
Status: Green/Red bicolor LED;
  Green light turns on in normal conditions;
  Red turns on in an abnormality.
  (Amber light turns on for approx. 1 second while the
  internal processor is initialized at the startup.)
Surge Protector: Green/Amber/Red tricolor LED indicating the surge protector life.
  OFF while no surge has been detected;
  Green when the first surge has been detected;
  Amber when the protector is close to the end of life;
  Red at the end of life.
  (Amber light turns on for approx. 1 second while the
  internal processor is initialized at the startup.)
LINK LED: Green LED indicating port link status.
  ON with a link established; Flashes during communication.
100M LED: Amber LED indicating data transfer rate;
  ON at 100 Mbps;
  OFF at 10 Mbps.
PC configuration: PC Confiugrator Software is used to program;
• LAN port operating mode (Default setting: Auto negtiation)
• User password
■ ALARM CONTACT OUTPUT
Turns on when the surge protector life ends,
when the power supply is lost,
or when an internal error is detected.
Rated load:
250 V AC @ 1.5 A (cos ø = 1)(applicable only to AC powered model.)
30 V DC @ 1.5 A (resistive load)
Minimum load: 5 V DC @ 10 mA
Mechanical life: 1 × 107 cycles (rate 180/min.)

LAN PORT

Standards: IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Number of ports: 8; All ports support AUTO-MDIX
(Automatically sensing cable type, straight-through or cross-over)
Data transfer rate: 10 Mbps (10BASE-T), 100 Mbps (100BASE-TX); Supports Auto-Negotiation
Cable: 10BASE-T (STP cable, category 5)
100BASE-TX (STP cable, category 5e)
Maximum segment length: 100 meters
Switching: Store & Forward
Flow control
Full duplex: PAUSE Frames
Half duplex: Back pressure
Buffer: 64 KB
MAC address table: 1024

INSTALLATION

•AC: Approx. 8 VA @ 100 V
Approx. 10 VA @ 200 V
Approx. 11 VA @ 264 V
•DC: Approx. 5.5 W
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 95 %RH (non-condensing)
Mounting: DIN rail
Weight
•AC powered: 650 g (1.4 lb)
•DC powered: 600 g (1.3 lb)

PERFORMANCE

Compliant standard: EN 61000-4-5 level X
  Between ports: 1kV (combination waveform)
  RJ-45 connector contact is out of the scope of this
  protection.  Using twisted-pair (STP) LAN cable is
  effective to reduce risk of fusing contact.
  Port to G: 10kV (combination waveform)
  FG (shield) to G: 15kV (combination waveform) with the shortcircuit bar
Voltage protection level
  Port to FG or G: 160 V min.
  Between each port: 160 V min.
  FG to G: 160 V min. (with the shortcircuit bar removed)
Insulation resistance: ≥ 100 MΩ with 100 V DC
(port or FG or G to alarm contact to power)
Dielectric strength: 2000 V AC @ 1 minute
(port or FG or G or power to alarm contact)
1500 V AC @ 1 minute
(port or FG or G to power)

STANDARDS & APPROVALS

The following standards are applied only to DC powered model.
EU conformity:
EMC Directive 
  EN 55032 Class A (EMI)
  EN 55035 (EMS)
RoHS Directive

EXTERNAL VIEW

CONNECTION DIAGRAM

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]