ES-8451 Rev.0

R3-NEIP2

Remote I/O R3 Series

EtherNet/IP INTERFACE MODULE

Functions & Features
• Converts analog and discrete I/O data to the open network fieldbus (EtherNet/IP)
Typical Applications
• Remote I/O for DCS and PLC

MODEL:R3–NEIP2-[1][2]

ORDERING INFORMATION

• Code number: R3-NEIP2-[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R3-NEIP2-R/CE/Q)
• Specify the specification for option code /Q
(e.g. /C01)

[1] POWER INPUT

N: No power supply
AC Power
M2: 100 – 240 V AC
(Operational voltage range 85 – 264 V, 47 – 66 Hz)*
(CE not available)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) *
* Not selectable for use with independent power modules or network modules with the internal power input options.

[2] OPTIONS (multiple selections)

Standards & Approvals
blank: Without CE
/CE: CE marking
Other Options
blank: none
/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to our web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating

RELATED PRODUCTS

• PC configurator software (model: R3CON)
• EDS file
The configurator software and EDS file are downloadable at our web site.
For connecting to PC, use commercially available Type-C USB cable. (provided by user)

GENERAL SPECIFICATIONS

Connection
Ethernet: RJ-45 Modular Jack
Internal bus: Via the Installation Base (model: R3-BSx)
Internal power: Via the Installation Base (model: R3-BSx)
Power input, RUN contact output: M3 separable screw terminal (torque 0.5 N·m)
Screw terminal: Nickel-plated steel
Isolation: EtherNet/IP to internal bus or internal power to power input to RUN contact output to FG
Input error data setting: Input value setting at input module error with side DIP SW
Dual communication setting: Set with the side DIP switch
Data allocation setting: Set with the side DIP switch
■ RUN CONTACT OUTPUT
RUN contact: Turns ON when both MS and NS LEDs are green (EtherNet/IP in normal communication).
Rated load: 250 V AC @ 0.5 A (cos ø = 1)
30 V DC @ 0.5 A (resistive load)
(Less than 50 V AC to conform with EU Directive)
Maximum switching voltage: 250 V AC or 30 V DC
Maximum switching power: 250 VA or 150 W
Minimum load: 1 V DC @ 1 mA
Mechanical life: 2 × 10⁷ cycles (300 cycles/min.)
When driving an inductive load, external contact protection and noise quenching recommended.

EtherNet/IP COMMUNICATION

Conformance test version: CT21
Communication standard: IEEE 802.3u
Transmission: 10BASE-T, 100BASE-TX
Baud rate: 10/100 Mbps (Auto Negotiation function)
Max. number of socket connections: 3
Connection type: Exclusive owner, Listen only, Input only
Protocol: EtherNet/IP
Transmission media: 10BASE-T (STP, Category 5) 100BASE-TX (STP, Category 5e)
Max. length of fieldbus segment: 100 meters
IP address: 192.168.0.1 (factory setting); Selectable with PC Configurator Software (model: R3CON)
Default gateway: 192.168.0.100 (factory setting); Selectable with PC Configurator Software (model: R3CON)
DLR supported
Port No.: 2222, 44818
I/O data area size: Input and output data area size set with side DIP SW
Required data words:
Input: 35, 67, 131, 252 words
Output: 35, 67, 131, 252 words (3 words are used only for status)
Ethernet indicator LED: TX/RX, LINK
MS (Module Status) indicator: Bi-color (green/red) LED indicates device status.
NS (Network Status) indicator: Bi-color (green/red) LED indicates status of the communication link.

INSTALLATION

Power consumption
•AC:
Approx. 20 VA at 100 V
Approx. 28 VA at 200 V
•DC: Approx. 12 W
Current consumption (no power supply): 70 mA
Output current (power supply): 280 mA continuous at 20 V DC; 430 mA for 10 minutes
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(EtherNet/IP to internal bus or internal power to power input to RUN contact output to FG)

STANDARDS & APPROVALS

EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive

EXTERNAL VIEW

TRANSMISSION DATA DESCRIPTIONS

MODULE STATUS, ERROR STATUS, DATA ERROR STATUS

I/O DATA DESCRIPTIONS

The data allocations for typical I/O modules are shown below.
Refer to the manual for each module for detailed data allocations.
■ ANALOG DATA (16-bit data, models: R3-SV4, YV4, DS4, YS4, US4, etc.)